Skip to main content

Computer software versions - Windows & Mac

There are numerous versions of the software as it evolves. The package is developed in Java and so requires the installation of the Java virtual machine. As I already have this, I can't comment on whether it will automatically install if it is absent. The versions are listed below with the most recent first.

December 29 2020

The latest downloads are found in the link below. At the time of writing, these are extremely slow, and can take 2-3 hours to download. Make sure you select the downloads for "K6" and the operating system you are working with.

There is a mirror of the field here on a Google drive. It is the same files, but download many times faster than the Wainlux-provided site.

Google Drive mirror

Wainlux download site


November 15 2020

*** As of December 29 2020, THESE LINKS ARE NOW GONE ***

The following software and firmware versions are tested by several owners and working. This is version 1.1.2


There are 2 identified issues:

  • The maximum engraving area is 80mm width x 75mm height
  • Accuracy settings "Moderate" and "Low" reduce the engravable area. The size of an 80mm image in the software and setting of "Moderate" is around 55mm square when engraved.

The Windows software also includes an option to update the firmware:







November 3 2020

The more cunning users experimented with the download link provided on the Kickstarter FAQ page for version 1.0.7, and discovered install_64_v1.0.8.exe.

Version 1.0.8 is also a non-functional version, but with a little more life. Looking in Windows Device Manager, you will see that it has created a COM port. However, all other issues remain. 


Download link - http://jiakuo25.0594.bftii.com/install_64_v1.0.8.exe

October 30 2020

The initial Kickstarter machine is delivered with a USB stick containing the PC software. It is named install_64_v1.0.7.exe. This software has not been reported as working by anyone. It will install and run, but you cannot import images or connect to the engraver.

Download link - http://jiakuo25.0594.bftii.com/install_64_v1.0.7.exe


By Labels:

Comments

  1. UnknownNovember 13, 2020 at 8:18 AM

    Under this link I got the version 1.1.1
    Windows:http://jiakuo25.0594.bftii.com/Laser_java_win.zip

    ReplyDelete
  2. UnknownNovember 13, 2020 at 8:20 AM

    And this one is for updating the mainboard
    Windows:http://jiakuo25.0594.bftii.com/K6_UP.zip

    ReplyDelete
  3. UnknownDecember 14, 2020 at 5:13 PM

    Hey guys, an update was released today.

    ReplyDelete
  4. UnknownNovember 6, 2021 at 12:46 AM

    I can't figure out how to install the software on my Win 10 machine. can someone direct me to a post or tell me how to get it to work? I get what looks like an install program to run but it's in chinese and nothing happens after i run it. Thanks!!

    ReplyDelete

Post a Comment

Popular posts from this blog

Cutting quality and times

By
Cutting mode on the Wainlux K6 engraver is much faster than the other engraving modes. This is because rather than scanning back and forth like a traditional printer, it follows the contours of the image. The test piece below is a good example that shows even complex contours - with lines inside lines - are possible in Cutting mode. Cutting mode is not just for cutting. With the right settings, it can be used to trace an image in wood or other materials. The obvious limitation is that you can't fill areas. With a little forward planning, it is possible to combine faster engraving of lines with slower engraving of more detailed areas. The equivalent image in Black or Greyscale mode takes around 45 minutes.  Using the logo from my daughter's business, I ran some tests for the cutting options. In all cases the engraving size is 70mm in diameter. Any settings that are not mentioned are left at their defaults. You will not see much difference in the photos, but please read the desc...
2 comments
Read more

Alignment Template II

By
 In a previous post I uploaded my Simple Positioning Template to align objects with the position of the laser. Although useful in my early tests and trials, I came to realise this is - in most cases - the wrong way around. I have found that it is better to create a template that sits on top of the object to be engraved. Here you can see my latest template in action. By using the preview function in the app, I can quickly align the engraving area to the template. Another little tip here is to reduce the power of the  weak light  to 3 or 4. you get a less intense beam that is easier to view and align. As you can see, the template has plenty of holes to view the surface below. The lines of the cutouts also help to align areas smaller than the full square. The image for the template is linked below. You can create your own from this image, I would recommend using card to create it. On a darker card like that shown in the photo, you can use cut mode (Panda 3 in the interface...
5 comments
Read more